/* Name : Sample Comm's Program - 1024 Byte Buffer - buff1024.c */
/* Written By : Craig Peacock <
cpeacock@senet.com.au> */
/* Copyright 1997 CRAIG PEACOCK <
cpeacock@senet.com.au> */
/* See
http://www.senet.com.au/~...erial1.htm */
/* For More Information */
#include <dos.h>
#include <stdio.h>
#include <conio.h>
#define PORT1 0x3F8 /* Port Address Goes Here */
#define INTVECT 0x0C /* Com Port's IRQ here (Must also change PIC setting) */
/* Defines Serial Ports Base Address */
/* COM1 0x3F8 */
/* COM2 0x2F8 */
/* COM3 0x3E8 */
/* COM4 0x2E8 */
int bufferin = 0;
int bufferout = 0;
char ch;
char buffer[1025];
void interrupt (*oldport1isr)();
void interrupt PORT1INT() /* Interrupt Service Routine (ISR) for PORT1 */
{
int c;
do { c = inportb(PORT1 + 5);
if (c & 1) {buffer[bufferin] = inportb(PORT1);
bufferin++;
if (bufferin == 1024) {bufferin = 0;}}
}while (c & 1);
outportb(0x20,0x20);
}
void main(void)
{
int c;
outportb(PORT1 + 1 , 0); /* Turn off interrupts - Port1 */
oldport1isr = getvect(INTVECT); /* Save old Interrupt Vector of later
recovery */
setvect(INTVECT, PORT1INT); /* Set Interrupt Vector Entry */
/* COM1 - 0x0C */
/* COM2 - 0x0B */
/* COM3 - 0x0C */
/* COM4 - 0x0B */
/* PORT 1 - Communication Settings */
outportb(PORT1 + 3 , 0x80); /* SET DLAB ON */
outportb(PORT1 + 0 , 0x0C); /* Set Baud rate - Divisor Latch Low Byte */
/* Default 0x03 = 38,400 BPS */
/* 0x01 = 115,200 BPS */
/* 0x02 = 57,600 BPS */
/* 0x06 = 19,200 BPS */
/* 0x0C = 9,600 BPS */
/* 0x18 = 4,800 BPS */
/* 0x30 = 2,400 BPS */
outportb(PORT1 + 1 , 0x00); /* Set Baud rate - Divisor Latch High Byte */
outportb(PORT1 + 3 , 0x03); /* 8 Bits, No Parity, 1 Stop Bit */
outportb(PORT1 + 2 , 0xC7); /* FIFO Control Register */
outportb(PORT1 + 4 , 0x0B); /* Turn on DTR, RTS, and OUT2 */
outportb(0x21,(inportb(0x21) & 0xEF)); /* Set Programmable Interrupt Controller */
/* COM1 (IRQ4) - 0xEF */
/* COM2 (IRQ3) - 0xF7 */
/* COM3 (IRQ4) - 0xEF */
/* COM4 (IRQ3) - 0xF7 */
outportb(PORT1 + 1 , 0x01); /* Interrupt when data received */
printf("\nSample Comm's Program. Press ESC to quit \n");
do {
if (bufferin != bufferout){ch = buffer[bufferout];
bufferout++;
if (bufferout == 1024) {bufferout = 0;}
printf("%c",ch);}
if (kbhit()){c = getch();
outportb(PORT1, c);}
} while (c !=27);
outportb(PORT1 + 1 , 0); /* Turn off interrupts - Port1 */
outportb(0x21,(inportb(0x21) | 0x10)); /* MASK IRQ using PIC */
/* COM1 (IRQ4) - 0x10 */
/* COM2 (IRQ3) - 0x08 */
/* COM3 (IRQ4) - 0x10 */
/* COM4 (IRQ3) - 0x08 */
setvect(INTVECT, oldport1isr); /* Restore old interrupt vector */
}
